Extron MAV Plus 128 Matrix Switcher driver for Windows 7 - Extron MAV Plus 128 Matrix Switcher driver from E

Extron MAV Plus 128 Matrix Switcher 1.06

Extron MAV Plus 128 Matrix Switcher driver from Extron for OS Independent

Extron MAV Plus 128 Matrix Switcher driver from Extron for OS Independent

Publisher review for Extron MAV Plus 128 Matrix Switcher 1.06:

Before install Extron MAV Plus 128 Matrix Switcher 1.06you should set a system restore point, to make sure you can rollback to your original driver in case you accidentally install another driver or select the driver for another version of the operating system.

Also, do not forget to check with our site as often as possible for new version of Extron MAV Plus 128 Matrix Switcher . We recommend to always use most recent version of a driver.

This package provides the necessary installation files of Extron MAV Plus 128 Matrix Switcher Firmware version 1.06.New features:Added support for new Matrix configurations:
- MVX 1212 VGA A Part # 60-838-01
- MVX 168 VGA A Part # 60-858-01
- MVX 1616 VGA A Part # 60-839-01
Fixes:- Corrected the configuration response of MAV Plus 16x8 series when firmware 1.04 is uploaded to the switcher. If you upgrade the firmware of the current MAV Plus 16x8 series (VA, SVA or HD A) from 1.03 to 1.04, the front panel and the “I” command would report a 16x16 configuration instead of 16x8. This has been corrected.
- Corrected the LS command response of the CrossPoint 450 Plus 8xN series. The vertical reading is now visible. This issue affected affects CrossPoint 450 Plus 8x4, 8x8, 8x16 HVA models and the sync rate reported through DSVP. When the individual sync frequencies (H & V) are read using the LS command, the horizontal rate was read correctly but not the vertical.
Note: This affects the SIS command & WCP responses. Webpage is OK.
- Corrected the part number N command response for the MVX 128 VGA A series. When using the N command with MVX 128 VGA series, the switchers would respond with the wrong part numbers (60-789-01 /-02). The correct response should be 60-799-01 /-02.
- Corrected the Genlock feature. The Genlock feature with MAV Plus models allowed switching to occur near the end of the vertical interval, which was visible in some display systems. This has been corrected.
- Corrected the audio output pop when making or breaking I/O ties without an audio source connected.
- Corrected the noise on audio outputs caused by the QS-FPC buttons. When the QS-FPC buttons are blinking (example pending ties), background illuminated or the button lights are on (example view mode), it produced a noise on the audio output. This has been corrected.
Installation steps:1. Download the firmware file.
2. Run the .exe file. This opens the Firmware Update program, creating a product named folder within which is placed the firmware file (x.S19).
3. Access the device internal web pages.
4. Select the Configuration tab.
5. On the Configuration page, click Firmware Upgrade on the left sidebar menu.
6. Click Browse. A Choose File window opens.
7. Navigate to the folder (created in 1g) where the firmware upgrade file is saved and select the file.
NOTES:
- Valid firmware files must have the file extension “.S19”. Any other file extension is not a firmware upgrade.
- The original factory-installed firmware is permanently available on the scaler. If the attempted firmware upload fails for any reason, the scaler automatically reverts to the factory-installed firmware.
8. Click Open .
9. Click Upload . While the firmware is uploading, the Upload button changes to “Uploading...” . When the uploading process is complete, the button changes back to Upload. The uploading may take a few minutes.

Operating system:
OS Independent